TPH Supply · Restroom repair guides
Need to replace a concealed stall latch? Start with the partition material.
Two bathroom stall latches can look similar and still require different replacement parts. Before ordering, identify the partition material, check for a manufacturer's name and photograph both sides of the existing latch.
This guide walks you through the information that helps our team match your concealed toilet partition door latch.
What does “concealed latch” mean?
A concealed latch assembly fits into an opening in the partition door. Parts of the operating assembly are still visible, so “concealed” does not mean that you cannot see the latch. Photograph the inside and outside hardware together to show the full arrangement.
A surface-mounted slide latch mounts on the face of the door. If you are unsure which style you have, send photographs before choosing a replacement.
1. Identify the partition material
Our first question is: What are your partitions made of?
- Metal (powder coated)
- Stainless steel
- Plastic laminate
- Solid plastic
- Phenolic
If you do not know, choose “I'm not sure” in Find My Latch. Include a wider view of the door and a clear photo of its edge so we can help.
Material narrows the possibilities, but material alone does not identify the correct latch. The door construction and existing hardware still need to match.
2. For metal partitions, check the outside latch face for a name
On a metal (powder-coated) partition, look at the latch face on the outside of the stall door—the side facing the restroom walkway. Look for a manufacturer's name stamped or marked on the hardware.
No name on that latch? Check the latches on other stalls in the same restroom. A name may still be readable on another door.
Write the name exactly as it appears and photograph it. If you find it on another stall, tell us that and include photos of the latch you actually need to replace.
3. Photograph both sides of the latch
Keep the hardware installed for the initial photos whenever possible. You do not need to take the latch apart just to begin an identification request.
- Inside close-up: Show the entire latch, operating bar or handle, and any visible mounting screws.
- Outside close-up: Show the complete outside face. Make any manufacturer's name readable.
- Wider inside view: Show the latch, door edge and the stop or keeper on the adjoining pilaster. The pilaster is the upright partition member beside the door.
Keep the camera steady and check that the small details are in focus. Include any broken or missing area rather than photographing only the loose replacement part you hope will fit.
4. Include the measurements and door swing you can confirm
Photos are the starting point. The following details help us check the replacement:
- Door thickness: Measure the door itself at its edge.
- Visible hardware size: Include the height and width of the latch face when possible.
- Mounting holes: If present and accessible, measure from the center of one hole to the center of the next.
- Door swing: Does the door open into the stall or outward toward the walkway? See our inswing and outswing guide.
- Existing opening: If the latch has already been removed, photograph and measure the opening. Do not disassemble it solely for this step.
Note the units and label what each measurement describes. If a measurement is uncertain, tell us rather than guessing.
Examples to compare after identification
These examples show why the manufacturer and door construction matter. They are starting points for comparison, not a fit chart.
| Example | What to check |
|---|---|
| Metpar 1509 concealed latch with flat bar | Used primarily with Metpar powder-coated steel and stainless steel doors. This model is not ADA compliant. Confirm the existing assembly and door details before ordering. |
| 1508 concealed latch with straight bar | Listed primarily for Global and General plastic-laminate partition doors. Compare the assembly, measurements and door construction. |
A matching chrome finish or similar-looking bar does not establish compatibility. If the details do not clearly match, use Find My Latch before purchasing.
Plan the complete repair before you order
Replacing the latch may be only part of the job. Check the surrounding hardware at the same time:
- Stop or keeper: Is it present, secure and compatible with the latch and door swing? Browse latch stops and keepers after confirming the match.
- Fasteners: Review what the selected assembly includes and which additional fasteners or driver bits your installation requires.
- Door condition: Show damage around the opening. A replacement latch alone may not address that damage.
- Multiple stalls: Count the doors needing repair and identify any differences. Do not assume every door uses the same hardware.
If the original latch cannot be matched, a suitable Fix-It Kit may provide another repair route by converting concealed latch operation to a surface-mounted slide latch. Match the kit to the door thickness, edge profile, swing and repair area. Kit contents vary, and the door must be able to support the repair hardware.
For several doors, request a quote with quantities, photos and delivery ZIP code. List different repairs separately.